Yesterday I installed a DVD+R/W drive in my hp pavilion 552w on the second
IDE Port as Master, with my (I believe this is right) Mitsumi CD-RW as slave.
My Hard Disk Drive (with HP Recovery Drive bundled inside) is on the primary
IDE as Master. Unfortunately, after I hooked everything backed up and turned
on the power, my computer started emitting a long, annoying beep at me and
refusing to do anything but light up the main power light and turn on the
fans. After much tinkering I finally got it to stop doing that, so that now
the motherboard will load, showing me the Boot-time diagnostic screen as
specified in BIOS. None of the drives are detected (all slaves and masters
after a pause are determined to be none), and if I don't press F1 to enter
Setup, my computer accesses my A: Drive trying to load a system disk (which I
of course do not have). I've tried hooking all the different four-pronged
power cords into each drive, even tried returning to the setup without the
DVD+R/W, but nothing seems to work. I really could do with some assistance
here, thanks.

The beep you got when you started usually indicates the type of problem
you're having. Beep codes are BIOS dependent and, since you didn't mention
the BIOS manufacturer, we can't answer unless someone knows if HP's all come
with BIOSes from the same manufacturer.

The owner's manual may list beep codes or you may have to go to the HP web
site and ask.

Adding the new device may have resulted in your exceeding the power output
of your power supply. What is the PSU rating and how much power does
everything in your system require? And, if it is the PSU, because you
exceeded it's limits, removing other items does not necessarily mean it will
now work - it may have suffered a major failure.

"Brandon S" <Brandon S@discussions.microsoft.com> wrote in message
news:FF926596-F34E-456A-AD29-B6FB321DF6B4@microsoft.com...
> Yesterday I installed a DVD+R/W drive in my hp pavilion 552w on the second
> IDE Port as Master, with my (I believe this is right) Mitsumi CD-RW as
> slave.
> My Hard Disk Drive (with HP Recovery Drive bundled inside) is on the
> primary
> IDE as Master. Unfortunately, after I hooked everything backed up and
> turned
> on the power, my computer started emitting a long, annoying beep at me and
> refusing to do anything but light up the main power light and turn on the
> fans. After much tinkering I finally got it to stop doing that, so that
> now
> the motherboard will load, showing me the Boot-time diagnostic screen as
> specified in BIOS. None of the drives are detected (all slaves and masters
> after a pause are determined to be none), and if I don't press F1 to enter
> Setup, my computer accesses my A: Drive trying to load a system disk
> (which I
> of course do not have). I've tried hooking all the different four-pronged
> power cords into each drive, even tried returning to the setup without the
> DVD+R/W, but nothing seems to work. I really could do with some assistance
> here, thanks.

GO into your bios and reset to default values!!!

your drives should then be recognized!!

"Brandon S" wrote:

> Yesterday I installed a DVD+R/W drive in my hp pavilion 552w on the second
> IDE Port as Master, with my (I believe this is right) Mitsumi CD-RW as slave.
> My Hard Disk Drive (with HP Recovery Drive bundled inside) is on the primary
> IDE as Master. Unfortunately, after I hooked everything backed up and turned
> on the power, my computer started emitting a long, annoying beep at me and
> refusing to do anything but light up the main power light and turn on the
> fans. After much tinkering I finally got it to stop doing that, so that now
> the motherboard will load, showing me the Boot-time diagnostic screen as
> specified in BIOS. None of the drives are detected (all slaves and masters
> after a pause are determined to be none), and if I don't press F1 to enter
> Setup, my computer accesses my A: Drive trying to load a system disk (which I
> of course do not have). I've tried hooking all the different four-pronged
> power cords into each drive, even tried returning to the setup without the
> DVD+R/W, but nothing seems to work. I really could do with some assistance
> here, thanks.

HP and Compaq Desktop PCs - Installing or Replacing a CD, CDRW, or DVD Drive
http://h10025.www1.hp.com/ewfrf/wc/d...=bph07164#N764

cable and jumper settings!!

"Brandon S" wrote:

> Yesterday I installed a DVD+R/W drive in my hp pavilion 552w on the second
> IDE Port as Master, with my (I believe this is right) Mitsumi CD-RW as slave.
> My Hard Disk Drive (with HP Recovery Drive bundled inside) is on the primary
> IDE as Master. Unfortunately, after I hooked everything backed up and turned
> on the power, my computer started emitting a long, annoying beep at me and
> refusing to do anything but light up the main power light and turn on the
> fans. After much tinkering I finally got it to stop doing that, so that now
> the motherboard will load, showing me the Boot-time diagnostic screen as
> specified in BIOS. None of the drives are detected (all slaves and masters
> after a pause are determined to be none), and if I don't press F1 to enter
> Setup, my computer accesses my A: Drive trying to load a system disk (which I
> of course do not have). I've tried hooking all the different four-pronged
> power cords into each drive, even tried returning to the setup without the
> DVD+R/W, but nothing seems to work. I really could do with some assistance
> here, thanks.

HP and Compaq PCs - BIOS Setup Utility Information and Menu Options
http://h10025.www1.hp.com/ewfrf/wc/d...dlc=en&lang=en

"Dixonian69" wrote:

> GO into your bios and reset to default values!!!
>
> your drives should then be recognized!!
>
> "Brandon S" wrote:
>
> > Yesterday I installed a DVD+R/W drive in my hp pavilion 552w on the second
> > IDE Port as Master, with my (I believe this is right) Mitsumi CD-RW as slave.
> > My Hard Disk Drive (with HP Recovery Drive bundled inside) is on the primary
> > IDE as Master. Unfortunately, after I hooked everything backed up and turned
> > on the power, my computer started emitting a long, annoying beep at me and
> > refusing to do anything but light up the main power light and turn on the
> > fans. After much tinkering I finally got it to stop doing that, so that now
> > the motherboard will load, showing me the Boot-time diagnostic screen as
> > specified in BIOS. None of the drives are detected (all slaves and masters
> > after a pause are determined to be none), and if I don't press F1 to enter
> > Setup, my computer accesses my A: Drive trying to load a system disk (which I
> > of course do not have). I've tried hooking all the different four-pronged
> > power cords into each drive, even tried returning to the setup without the
> > DVD+R/W, but nothing seems to work. I really could do with some assistance
> > here, thanks.